Rewiring a Motion Sensor Light in 6 Simple Steps

A motion sensor is a device that converts the detection of motion into electricity. Whenever it senses any motion taking place it turns the lights on automatically. If this fails to happen then your motion sensor light needs to be rewired. The rewiring of a motion sensor light is easy if you carry out the proper procedure and preserve safety.

1. The first and the most common step is to turn the circuit breaker off from the central board.
2. Now switch on the light and check whether it is on or off with the help of a tester. The tester will light if the sensor is still on. Carry on with the process ones you are sure that the sensor is off.
3. Take a screwdriver and remove the junction box plate. Ones the junction box is taken off twist the wire nuts.

Learn the Procedure of How to Install a Light Timer

Light timers are guides that help you find out the heavy-duty lights that are kept on in your house. Keeping light on unnecessarily can result in a tremendous loss of energy. Installing light timers can ensure that the lights are turned off and help in saving a lot of precious energy. Installing a light timer in your house is an extremely easy and trouble-free process to perform.

1. First step is to turn off the main switch from the circuit breaker.
2. Take a screwdriver and unscrew the faceplate of the light switch. Remove the plate out and check whether the electricity is not been passed with the help of a tester.
3. If the electricity is off then carry on with the process. Remove the wire connectors by unscrewing the old lights from the walls. This way the lights will be disconnected.

How to Join Two Telephone Cables

You must have seen houses where there are two telephone lines attached. If you are wondering how this can be possible, then i give you the answer. This is possible with the use of a RJ11 coupler. RJ11 coupler is a connector on the conclusion of the phone cable. You can connect two RJ11 cables to get two different phone lines. Its application is extremely simple:

1. First take one phone line and connect it to one of the RJ11 ports on the coupler.
2. Now connect the other end of the phone line to the wall jack.
3. Now take the second phone line and connect it to the other RJ11 slot on the coupler.
4. Connect the other end of the line to the RJ11 port on the phone. Your connection is complete.

How to Reseat USB & Power Cables

Re-seating a USB or a power cable is an easy task to do. USB or power cables are the equipments that attach you’re the peripheral equipment, such as computers, hard drives, printers, modems, cameras, etc. to its power supply. These power cables become loose, so it is important to check them form time to time. If these cables become loose, your equipment will not work. Some precautions needs to taken before re-seating a USB or a power cable.

1. Firstly, shut down or switch off the equipment to which the cable is attached.
2. Take out the plug out of the socket slowly by switching the power switch off.
3. Now properly insert the cable back into the power socket. Make sure that the plug is fully inserted into the socket.

How to Troubleshoot Electric Motor Starters

If your electric motor starter is facing problems then its troubleshooting can be a problematic task. But ones you have thoroughly understood its basics then troubleshooting can be done without mush trouble. Follow these steps to troubleshoot an electric motor starter:

1. The first step to perform is to wear safety glasses and switch off all the connections. Take all the precautions before starting the troubleshooting. Switch off the volt-ohm meter to volts and place the leads to the incoming power. The voltage should read 0.
2. Check that all the screws are tight with the help of a screwdriver. Also heck the wires for any burnt or black discoloration. If so, then immediately replace the wires with a new one.

How an Electric Brake Motor Works

Theory:

Electric motor brakes can basically make an electric motor turn backwards. The motor brakes supply the electric motor with an external force, instead of an electric force to make the shaft in the motor run. This external force is usually applied by the wheels of the car that generate electricity.

Working:

There are two separate coils of wire in a motor that are located constructively around a permanent magnet which is connected to the central shaft. When electricity passes through these wires, a magnetic field is generated that makes the motor work. The central magnet alternates and results in a continuous feeling of rotation on the magnet. As per the alignment of the central magnet, the magnetic field turns on and off consecutively, thus making the magnet turn.

Learn How a Gear Motor Works

A gear motor is basically a type of electric motor. Just as an electric motor, a gear motor also does not electricity to rotate the blade connected to the shaft. It makes use of an external force to rotate the shaft. This external force is converted into electricity to run the motor. In a gear motor, the energy produced is consumed to rotate a sequence of gears in a cohesive gear train.

There are two main types of gear motors viz. AC (alternating current) and DC (direct current).

Purpose:

The gear reduction system or the gear box is the integral part of a gear motor. The gear box contains either permanent magnets or electromagnets which produces magnetic current. A shaft is connected to the gear box that helps in aggregating the quantity of continuous torque the motor can produce and at the same time reduces the motor's output speed. This is the reason that the motor will not need to pull much current to work and will move slowly and deliver more current.

How to Make Different Types of Fire starters in different methods

Lighting up a fire in a serene place is the most difficult task to perform. Fire starters are devices that are considered as the most reliable way of generating a fire in the backwoods or wilderness. A fire starter can help you lit fire with ease in any type of situation. Instead of buying a fire starter and spending big bucks, all you can do is make one on your own.

Below are some of the ways in which you can make a home-made fire starter:

1. The finest and the most ancient way of lighting fire is by using flint and steel. Flint is a type of stone which when collided with a piece of steel forcefully, can produce hot sparks. These hot sparks are beneficial enough to light dry tinder.
2. The second method is by using a web belt or a hiking compression band. First of all cut the old, damaged web belt or hiking compression band into 8 cm strips. Soak these strips in wax and let them dry for a while. Now whenever you need light, use them as candle.